Browsing by Keyword "Photovoltaic module"
Now showing 1 - 4 of 4
Results Per Page
Sort Options
Item Composite material incorporating protective coatings for photovoltaic cell encapsulation(2022-09-15) Yurrita, Naiara; Aizpurua, Jon; Cambarau, Werther; Imbuluzqueta, Gorka; Hernández, Juan M.; Cano, Francisco J.; Huerta, Irene; Rico, Elena; Caño, Teodosio del; Wölper, Sarah; Haacke, Florian; Zubillaga, Oihana; Tecnalia Research & Innovation; SISTEMAS FOTOVOLTAICOS; SGPhotovoltaic modules consisting of one back-contact cell were manufactured by vacuum resin infusion process using glass reinforced epoxy composite as encapsulant where the cells are embedded. Incorporation of three coatings onto the composite surface was studied with the aim to improve the electrical performance stability of the modules under ultraviolet (UV), thermal cycling and damp-heat environmental weathering. Photovoltaic and aging performance were examined through the short-circuit current density values and colour change of the composite. Decrease in the initial photovoltaic performance of the modules was caused by the coating deposition. The highest drop in the initial values was observed for the varnish type coating, showing a decrease of 2.6% in short-circuit current. Regarding the performance stability, the decrease was more pronounced in the damp-heat test, presenting the varnish type coating the minimum loss of 1.4% in short-circuit current and a variation of 87% in b* chromatic parameter after 1000 h exposure at 85 °C and 85% relative humidity. The study concluded that the protective coating should be selected to provide the composite modules with an optimal trade-off between the initial electrical performance and the desired stability, with further research work targeted to improve moisture barrier properties.Item Composite material with enhanced ultraviolet performance stability for photovoltaic modules(2019-09-15) Imbuluzqueta, Gorka; Yurrita, Naiara; Aizpurua, Jon; Cano, Francisco J.; Zubillaga, Oihana; SISTEMAS FOTOVOLTAICOS; SGThe present work aims encapsulating photovoltaic cells in glass reinforced epoxy composite by vacuum resin infusion, incorporating additives directed to enhance the performance stability of the manufactured photovoltaic modules under ultraviolet (UV) exposure. UV absorber (UVA) and hindered amine light stabilizer (HALS) additives were incorporated in the resin system in different content. Photovoltaic performance and stability under UV radiation exposure were studied through external quantum efficiency (EQE) spectra, chromatic coordinates and short-circuit current values. Decrease in current values and increase in yellowness were observed in the presence of UVA and HALS. However, an enhanced performance stability was observed when additives are incorporated, improving the stability when increasing the additive amount. The most stable module, with cells embedded in 2% additive containing composite, showed a 2.7% short-circuit current loss after UV aging exposure.Item Optical model for multilayer glazing systems: Application to laminated glass and photovoltaic modules: Application to laminated glass and photovoltaic modules(2016-02-01) Baenas, Tomás; Machado, Maider; Tecnalia Research & InnovationThis article provides theoretical developments broadening the scope of previous optical simulation models for multilayer glazing systems. The applicability of existing models will be extended through additional characterization of the multilayer optical components from global spectrophotometric (UV–vis–NIR) measurements. A more complete interlayer film characterization, including reflectivity in the film–glass interface, will be provided. Singular solutions of the related equation systems will be derived for situations involving components with very low or null transmissivity. As a contribution to the fundamentals of the formalism, the condition relating the symmetry of the transmittance of the system with the symmetry of the transmissivity of its optical components will be studied. Finally, with the extension for the calculation of energy fluxes through the components of a multilayer system, analytical expressions for the components absorptivity will be derived. These results are particularly useful to quantify differences in energy absorption of the constituents of a laminated glass, as a tool to define, from the glazing design phase, the thermal and mechanical processing needed for each glazing component. Additionally, the model provides a procedure for the calculation of the absorptivity of encapsulated photovoltaic cells, which is directly related to cell efficiency in each particular configuration.Item Photovoltaic modules encapsulated in composite material modified with ultraviolet additives(2021-09-15) Yurrita, Naiara; Aizpurua, Jon; Cambarau, Werther; Imbuluzqueta, Gorka; Hernández, Juan María; Cano, Francisco J.; Zubillaga, Oihana; Tecnalia Research & Innovation; SISTEMAS FOTOVOLTAICOS; SGPhotovoltaic modules were manufactured by vacuum resin infusion process using glass reinforced epoxy composite as encapsulant where the cells are embedded. Incorporation of ultraviolet absorber (UVA) and hindered amine light stabilizer (HALS) additives to the epoxy resin was studied, given their potential to enhance the performance stability of the modules under ultraviolet (UV) radiation exposure. Photovoltaic and aging performance were examined through the evolution of external quantum efficiency (EQE) spectra, short-circuit current values and colour change. Decrease in the initial photovoltaic performance of the modules was observed, as evidenced in the short-circuit losses when additives are incorporated. Regarding the performance stability, increasing the content of both, UVA and HALS, leaded to improved results with lower short-circuit current loss and yellowness observed due to UV radiation. The most stable module, with cells embedded in 1% UVA and 1% HALS containing composite, showed a 2.8% short-circuit current loss after an UV exposure of 15.4 KWh/m2. UV protection enhancement was obtained in trade-off with initial photovoltaic performance, which should be considered when defining the additives and the amount to be used.